Overview

4.2 VOC High Solids Spot Repair Urethane Clearcoat Kit with Standard (65 to 90ºF) Temperature Hardener

European Style Clearcoat - Ideal for cold weather or for use as a spot repair clear.

Kit Includes:

• 1 Gallon of U-POL UP2892 (4.2 VOC) High Solids Urethane Clearcoat
• 1 Liter of U-POL UP2323 Standard Hardener (Makes 1 1/4 Sprayable Gallons = Aprox. 5 Liters)

NOTE: This Clearcoat meets the 4.2 National VOC Rule, but is not compliant for sale in California and Canada and will not be sold in either California or Canada.

High Solids Urethane Spot & Panel Repair Clearcoat with a 4 to 1 Mixing Ratio

UP2892 is a HS two component acrylic urethane coating with Nanoparticulate technology which is the essential key in obtaining scratch resistant surfaces (SRC). Plus, it gives the clear a rubber-like elasticity as well as minimizing interaction between individual polymeric chains. Making UP2892 very resistant to rock chips, dust abrasion and normal weathering.

Features & Benefits:

• Easy to apply with excellent flow and non-sag properties.
• Hardens rapidly to give a high build U.V resistant coating.
• Excellent gloss and long term durability.
• Can be air dried, low baked or I.R. cured.
• Can be easily polished once cured.

Nano Particulate Clear Features:

• The SRC resins provide improved scratch and abrasion resistance
• Deep wet-look gloss and transparency
• 72 hour buff window
• Barrier against gases, water and solvents
• Increased weather resistance (acid rain)
• Reduced shrinkage and heat reaction
• Improved adhesion to ALL substrates
• Better dirt resistance
• HS ... Higher solids
• Solvent and Waterborne compatible

Surface Preparation:

1. Degrease with wax and grease remover, UP2002, UP2012 or UP2023
2. Abrade the surface, Original cured paint Wet sand with P800-1000 Or dry sand with P600-800, then wipe again with degreaser
3. Remove dust and containments that may have settled with a tack cloth UP0430 or UP0431
4. Apply basecoat to the manufactures directions

Application:

1. Apply basecoat to the manufactures directions.
2. Apply two wet coats: Film build 1.5- 2.0 mil Conventional Gravity: 1.3mm -1.4mm 2 bar or 28-30 psi at gun Siphon: 1.3mm -1.4mm 2 bar or 28-30 psi at gun HVLP Gravity: 1.3mm -1.4mm 8-10 psi at gun
3. Allow 5-10 minutes flash between coats.
4. Dry Times at 68°F
DUST FREE: 10-12 minutes depending on hardener selection
TACK FREE: 15-20 minutes depending on hardener selection
FORCE DRY: 20-40 minutes at 140°F (60°C)
INFRA RED: 15 minutes
BUFF TIME: After cool down from force dry or Minimum 6-8 hours air dry; maximum 72 hours

REPAIRING & RECOATING: may be recoated after a 5 Hour dry at 77°F, or after a minimum 1 hour cool down after force drying at 140°F for 30 minutes

POT LIFE: 4-6 hours :

1. Apply basecoat to the manufactures directions.
2. Apply two wet coats: Film build 1.5- 2.0 mil Conventional Gravity: 1.3mm -1.4mm 2 bar or 28-30 psi at gun Siphon: 1.3mm -1.4mm 2 bar or 28-30 psi at gun HVLP Gravity: 1.3mm -1.4mm 8-10 psi at gun
3. Allow 5-10 minutes flash between coats.
4. Dry Times at 68°F
DUST FREE: 10-12 minutes depending on hardener selection
TACK FREE: 15-20 minutes depending on hardener selection
FORCE DRY: 20-40 minutes at 140°F (60°C)
INFRA RED: 15 minutes
BUFF TIME: After cool down from force dry or Minimum 6-8 hours air dry; maximum 72 hours
REPAIRING & RECOATING: may be recoated after a 5 Hour dry at 77°F, or after a minimum 1 hour cool down after force drying at 140°F for 30 minutes
POT LIFE: 4-6 hours

Additives:

Accelerator - If an accelerator is needed, use our Rocket (UP2000-UP0735) follow directions on use.

Fish Eye - The use of fish eye eliminator is strongly discouraged. If a fish eye additive is needed, use UP2001. Use no more than Necessary as it will directly affect the flow.

Painting Flexible Parts - An additive is not required for any flexible substrate

Blending - Dry edges can be blended in with Fade Out (UP2433).